MS-20M Kit + SQ-1
MONOPHONIC SYNTHESIZER MODULE KIT
Support for Your Purchase
Support
Learn More
Related Products
News
Package contents of MS-20 Kit
Top panel, Bottom panel, Left side pane, Right side panel, Spacer sheet, Junction circuit board (small), Junction circuit board (large), Rear jack circuit board unit, VR circuit board (small), VR circuit board (large), Panel jack circuit board & switch VR circuit board, TRIG SW button, Nut A (x92), Washer A (x46), Nut B (x7), Nut C (x30), knurled nut (x3), Screw A (x4), Screw B (14), Spacer, Rubber bushing (x14), Rubber feet (x4), Knob (large) (x7), Knob (small) (x29), Cord hook, Box-end wrench (included), Mini-wrench (included)
MS-20M Kit Main Specifications
- Connectors
- Signal IN jack (1/4" phone jack), Signal OUT jack (1/4" phone jack, 2Vp-p output impedance 3.5kΩ), PHONES jack (1/4" Stereo phone jack, 33Ω 48mW), DC12V jack, MIDI IN, USB type B
- Power Supply
- DC12V
-
Dimensions
(W) x (D) x (H) - 587 mm x 215 mm x 104 mm /23.11" x 8.47" x 4.09"
- Weight
- 4 kg / 8.82 lbs.
- Accessories
- Ten ø6.3 mm patch cables, three ø3.5 mm, patch cables, AC adapter (12V)
MS-20M Kit Specifications in details
- Control Section
- 1. Voltage Controlled Oscillator 1(VCO 1)
-
:Scale (32', 16', 8', 4') (6 octaves, +cent, -cent)
:Wave form(Triangle, Sawtooth, PW-Square, White Noise) (4 modes)
:Pulse width adjust 1:1 ～ 1:infinity - 2. Voltage Controlled Oscillator 2(VCO 2)
-
:Scale (16', 8', 4', 2') (6 octaves, +cent, -cent)
:Wave form(Sawtooth, Square, Pulse, Ring modulator) (4 modes)
:Pitch(± 2 octave) - 3. VCO Master control : Master tune(± 100cent)
-
:Portamento(max. 10sec)
:Frequency modulation intensity by MG/T.EXT(-5V ～ +5V)
:Frequency modulation intensity by EG1/EXT(-5V ～ 0V) - 4. VCO Mixer
-
:VCO 1 Level
:VCO 2 Level - 5. Sync
- :On/Off Slid SW(VCO1-->VCO2)
- 6. FM
- :On/Off Slid SW(VCO1-->VCO2)
- 7. Voltage Controlled High Pass Filter (VCF HPF)
-
:Cutoff frequency(50Hz ～ 15,000Hz)
:Peak(flat ～ self OSC)
:Cutoff frequency modulation intensity by MG/T.EXT(-5V ～ +5V)
:Cutoff frequency modulation intensity by EG2/EXT(-5V ～ +5V) - 8. Voltage Controlled Low Pass Filter (VCF LPF)
-
:Cutoff frequency(50Hz ～ 15,000Hz)
:Peak(flat ～ self OSC)
:Cutoff frequency modulation intensity by MG/T.EXT(-5V ～ +5V)
:Cutoff frequency modulation intensity by EG2/EXT(-5V ～ +5V) - 9. Filter Type
- :Select Slide SW(REV.1 / REV.2)
- 10. Envelope Generator 1
-
:Delay time(10sec)
:Attack time(10sec)
:Release time(10sec) - 11. Envelope Generator 2
-
:Hold time(20sec)
:Attack time(10sec)
:Decay time(10sec)
:Sustain level(0V ～ 5V)
:Release time(10sec) - 12. Modulation Generator (LFO)
-
:Wave form(Negative Sawtooth ～ Triangle ～ Positive Sawtooth, Wide Pulse ～ Square ～ Narrow Pulse)
:Frequency(0.1Hz ～ 20Hz) - 13. Power switch and Volume
- :Volume
- 14. Indicator
- :LED(Power On, EG1+EG2 trigger, Modulation Generator rate)
- External Signal Processor
- 1. Control section
-
:Input signal level
:Low cut frequency(50Hz ～ 2,500Hz)
:High cut frequency(100Hz ～ 5,000Hz)
:CV adjust
:Threshold level - 2. Input and Output
-
:Signal In
:Amplifier Out
:Band pass filter Out
:CV Out(0 ～ +8.4V)
:ENV Out(0 ～ +5V)
:Trig Out(+5V-->GND) - 3. Indicator(LED)
-
:Peak indicator
:Trigger indicator
- Patch Panel
- 1. CV IN(Hz/V)
- :VCO 1 + VCO 2 control voltage input(Hz/V 0 ～ +8V)
- 2. CV IN(V/Oct)
- :VCO 1 + VCO 2 control voltage input(V/Oct 0 ～ +5V)
- 3. CV OUT
- :VCO control voltage output(Hz/V) (0 ～ +8V Caution: only MIDI IN)
- 4. TRIG OUT
- :Trigger output(+5V-->GND Caution: only MIDI IN)
- 5. VCO
- :VCO 1 + VCO 2 external frequency control input(V/Oct -5V ～ +5V)
- 6. PWM IN
- :PWM for VCO 1 PW-Square
- 7. VCF
-
:External signal input(3Vp-p max.)
:External High pass filter cutoff frequency control input(2OCT/V)(-5V ～ +5V)
:External Low pass filter cutoff frequency control input(2OCT/V)(-5V ～ +5V) - 8. VCO + VCF
- :Total external modulation input(T.EXT)(-5V ～ +5V)
- 9. VCA
- :External initial gain control input(0 ～ +5V)
- 10. EG
-
:EG 1 envelope signal normal output(0V 〜 +5V)
:EG 1 envelope signal reverse output(+5V ～ 0V)
:EG 1 + EG 2 trigger input(GND-->+5V ～ +15V)
:EG 1 + EG 2 trigger input(-->GND)
:EG 1 trigger input(-->GND)
:EG 2 envelope signal normal output(0V ～ +5V)
:EG 2 envelope signal reverse output(+5V ～ -5V Caution: Sustain Level=0V) - 11. MG
-
:Triangle output(Negative Sawtooth ～ Triangle ～ Positive Sawtooth)(5Vp-p)
:Rectangle output(Wide Pulse ～ Square ～ Narrow Pulse)(0 ～ +5V) - 12. Noise Generator
-
:Pink noise output(5Vp-p)
:White noise output(5Vp-p) - 13. Sample and Hold
-
:Clock trigger input(-->GND)
:Sample signal input(5Vp-p max.)
:S/H output(5Vp-p max.) - 14. Modulation VCA
-
:Control voltage input(0 ～ +5V)
:Signal input(-5V ～ +5V)
:Signal output(-5V ～ +5V) - 15. TRIG SW
- :SW On-->TRIG IN(-->GND)
- 16. TRIG SW OUT
- :Switch output(-->GND)
- 17. JUNCTION
- :3 x (1 x 3.5mm Stereo mini Phone Jack + 3 x 6.3mm Stereo Phone Jack)
- Connectors
- 1. Signal In
- : Monaural phone jack
- 2. Signal out
-
: Monaural phone jack
: Maximum Output Level 2Vp-p
: Output Impedance 3.5kΩ - 3. Head phones out
-
:Stereo phone jack
:Maximum Output Level 48mW (33Ω)
:Output Impedance 10Ω - 4. MIDI
-
：MIDI Input
* Only note messages (velocity is not used) can be received
* MIDI CH (1 - 16) can be changed - 5. USB
-
:Type B, USB-MIDI Input/Output
* Only note messages (velocity is not used) can be transmitted and received
* MIDI CH (1 - 16) can be changed
- General
- Power Consumption
- : 9.24W
- Power Supply
- : DC12V
-
Dimensions
(W) x (D) x (H) - 587 x 211 x 104 mm /23.11" x 8.31" x 4.09"
- Weight
- 4 kg / 8.82 lbs.
- Accessories
- AC adapter (12V), ten ø6.3 mm patch cables, three ø3.5 mm patch cables
SQ-1 Specifications
- Sequencer Mode
- ALTERNATE、ORDER、PARALLEL TURN、PARALLEL ORDER、CV/DUTY、CV/SLIDE、CV/DUTY | RANDOM、RANDOM
- Step Mode
- GATE ON/OFF、ACTIVE STEP、SLIDE、STEP JUMP
- Sequence Step Resolution
- quarter notes, eighth notes, sixteenth notes
- CV OUT Pitch
- Linear, Minor, Major, Chromatic
- CV OUT Voltage
- 1V, 2V, 5V (Oct) 8V (/V)
- GATE OUT Polarity
- + (positive polarity), - (negative polarity)
- SYNC IN/OUT Polarity
- + (rise), - (fall)
- Connectors
-
- littleBits OUT jack (mini monaural phone jack)
- OUT (MIDI OUT) jack (mini stereo phone jack)
- CV - A OUT - GATE jack (mini monaural phone jack, CV OUT : Output level 1V, 2V, 5V, 8[Hz/V], GATE OUT: output level 10V)
- CV - BOUT - GATE jack (mini monaural phone jack, CV OUT : Output level 1V, 2V, 5V, 8[Hz/V], GATE OUT: output level 10V)
- IN – SYNC – OUT jack (mini monaural phone jack, SYNC IN: Max input level 20V, SYNC OUT: Output level 5V)
- USB jack (type B, USB MIDI)
- Power Supply
- Two AA batteries (alkaline batteries recommended), or USB power
- Battery Life
- approximately 5 hours (when using alkaline batteries)
-
Dimension
(W x D x H) - 93 x 84 x 63 mm/7.60" x 3.31" × 2.48"
- Weight
- 641 g/1.41 lbs.
- Accessories
- Two AA batteries for checking operation, mini plug – DIN cable
- Options
- Patch cable MS-CABLE-18
| * All product, company, and standard names are trademarks or registered trademarks of their respective holders. * Appearance and specifications of products are subject to change without notice. |
MS-20M Kit + SQ-1
MONOPHONIC SYNTHESIZER MODULE KIT
Related Products
Sitemap
Copyright © 2024 KORG Inc. All Rights Reserved.
Choose Your Location 
We use cookies to give you the best experience on this website. Learn more
Got it